BookTitleMAGNET_GENERAL_CATALOG

Summary

MAGNET_GENERAL_CATALOG

OFF120806016.752 10 39101140100110200O NOFFON OFFModel HL HAND LIFMA*HL-15 HL-20A�E�Application�E�Suitable for pulling out steel materials or steel plates and carrying metal frames, raw materials,press molds, semi-fi nished products, etc.�E�Features�E�●A new cam mechanism is employed so as not to apply friction due to holding and releasingdirectly to the surface of workpieces to transport. (HL-20A)●Workpieces are held and released quite smoothly.●The magnetic force can be turned on and off by lever operation. (HL-15)●The T-handle is robust and held by hand comfortably for stable workpiece transportation. (HL-15)Holding ReleasingModelMax. Holding Power LiftingCapacityDimensions HandleLength MassLateral Lift Width Length HeightHL-15 350N�E�E5kgf�E�E1.5kN�E�E50kgf�E�E20kg/44.1 lb 60�E�E.36�E�E20�E�E.72�E�E52�E�E.04�E�E49�E�E.92�E�E3.0kg/6.6 lbHL-20A 500N�E�E0kgf�E�E2 kN�E�E00kgf�E�E30kg/66.1 lb 100�E�E.93�E�E40�E�E.51�E�E32�E�E.26�E�E200�E�E.87�E�E2.5kg/5.5 lb※The holding power is based on a test piece of 15 mm thick soft steel. The holding power and lifting capacity dropdepending on the thicknesses, materials of workpieces and other factors.　※Do not use this Lifma for a hoist.�E�mm�E�En�E�］How to use (HL-20A)PL-40B�E�Application�E�These Lifmas are suitable for transporting such raw materials as mill scale ironplates and fl at iron products and lifting and transporting semi-finished productshaving flat surfaces such as machine parts, press dies and plastic molds.�E�Features�E�●These are of permanent magnetic type requiring no power source. Thus, thereis no risk of falling workpieces due to power failure or failure of wiring systems.●The employment of a cam system facilitates holding and releasing of workpieces.�E�Application�E�Suitable for lifting and moving bent plates, floor plates, pressed workpieces havingconcave or convex sections, iron doors of buildings, deck plates, guard rails, cans, etc.�E�Features�E�●The attraction is turned on and off by moving up and down the built-in magnetwith an air cylinder, which facilitates remote operation and automated operation.●Compared with the electromagnetic type, this model has a larger holding poweron thin sheets (less than 5 mm thick) and its capacity drops less whenclearance is present. Accordingly, this model is most suitable for lifting pressedworkpieces having concave or convex sections.●Energy saving type as no electric power source is required.●The ON state is maintained if the air source is shut down and therefore there isno risk of falling workpieces, thus enhancing safety.Model PL PERMANENT MAGNETIC LIFMA*Model LM-P UP-DOWN TYPE PERMANENT MAGNETIC LIFMA*dL BH■HoldingPlace the Lifma on a workpieceto transport and pull the leverupright.■ReleasingPut the lever in the horizontalposition to release the Lifmafrom the workpiece.�E�mm�E�En�E�］Model LiftingCapacityDimensions Shackle“d ELifting ring ID) MassB L HPL-20B 200kg/440 lb 122�E�E.80�E�E255�E�E0.0�E�E50�E�E.90�E�EBC14�E�E.55�E�（ρE0�E�E.57�E�！E8.5kg/18lbPL-40B 400kg/881 lb 212�E�E.34�E�E181�E�E.12�E�EBB20�E�E.78�E�（ρE8�E�E.28�E�！E14.0kg/31lb※The lifting capacity is indicated by a quarter of the max. holding power.※The dimension “H Eis up to the top end of the inside diameter of the shackle.■Steel plate lifting standard (Mill scale soft steel plate) �E�mm�E�En�E�］PL-20B PL-40B5ー7 □450�E�E7.7�E�E350�E�E3.7�E�ÁE50�E�E1.6�E�E□950�E�E7.4�E�E650�E�E5.5�E�ÁE300�E�E1.1�E�Eー12 □500�E�E9.6�E�E350�E�E3.7�E�ÁE00�E�E7.5�E�E□1100�E�E3.3�E�E750�E�E9.5�E�ÁE500�E�E9.1�E�E3ー16□550�E�E1.6�E�E400�E�E5.7�E�ÁE00�E�E7.5�E�□1000�E�E9.4�E�E700�E�E7.5�E�ÁE400�E�E5.1�E�E7ー25 □950�E�E7.4�E�E650�E�E5.5�E�ÁE300�E�E1.1�E�E6ー40 □450�E�E7.7�E�E350�E�E3.7�E�ÁE50�E�E1.6�E�E□750�E�E9.5�E�E550�E�E1.6�E�ÁE000�E�E9.4�E�E1ー65 □350�E�E3.7�E�E250�E�E.84�E�ÁE00�E�E9.6�E�E□600�E�E3.6�E�E450�E�E7.7�E�ÁE00�E�E7.5�E�E6ー100 □250�E�E.84�E�E200�E�E.87�E�ÁE00�E�E1.8�E�E□500�E�E9.6�E�E350�E�E3.7�E�ÁE00�E�E7.5�E�ModelThicknessPrecautions for useWhen you plan to use the Lifma for special steel materials such as hardened materials,please consult with us prior to purchasing the Lifma.The operation of the cam to hold and release workpieces exerts physical friction to theworkpieces. Therefore, the surfaces fi nished by polishing, for example, may be scratched.Do not use the Lifma for workpieces whose width or length is short and the camoperation does not work on them. Operate the ON/OFF select cam by a foot.4�E�MON側OFF側50ストロークL 1LdW1H h2-3/8W□ModelDimensionsAir Pressure MassW L H h W1 L1 d MLM-P1242 120�E�E.72�E�E20�E�E6.5�E�E12�E�E.40�E�E93.5�E�E.68�E�E80�E�E.14�E�E370�E�E4.5�E�E98�E�E.85�E�EM12�E�E 0.47�E�depth 14�E�E.55�E�E.49 MPa or overApprox. 17kg/ 37 lbLM-P2442 240�E�E.44�E�E119�E�E.69�E�E133�E�E.23�E�E150�E�E.90�E�E300�E�E1.8�E�E142�E�E.59�E�EM20�E�E 0.78�E�depth 30�E�E.18�E�EApprox. 38kg/ 83 lb※An air source, select valve and other air control equipment must be provided by the user.※This model is not suitable for thick workpieces and workpieces stacked closely. The specifications vary according to workpieces to lift. Please contact us to select the best design.�E�mm�E�En�E�］An exampleof usageLM-P1242An example of special fabrication97 LIFTINGMAGNETMAGBORE* CHIP & SLUDGECONVEYANCE EQUIPMENTENVIRONMENTALEQUIPMENTMAGNETIZER ANDDEMAGNETIZERMAGNETIC EQUIPMENTFOR CONVEYANCEMAGNETICSEPARATORSMEASURINGTOOLSPOWERFUL MAGNETICSEPARATORSMEASURINGINSTRUMENTSMAGNETICMATERIALSMAGNETIC TOOLS & EQUIPMENTFOR WELDING OPERATIONLIFTING MAGNETS