Summary
MAGNET_GENERAL_CATALOG
QS7 QS5 QN7 QN5PowerfulModel with T-slots available・ｩ・ｮ・ｰ・ｵ・ｴ縲縲・｡・｣・抵ｼ撰ｼ撰ｼｶ・ｫ・｡・ｮ・･・ｴ・･・｣縲・｣・ｯ・趣ｼ鯉ｼｬ・ｴ・､・弱・ｪ・｡・ｰ・｡・ｮ・･・ｰ縲・｣・ｨ・ｵ・｣・ｫ縲・ｭ・｡・ｳ・ｴ・･・ｲ・ｯ・ｵ・ｴ・ｰ・ｵ・ｴ縲・呻ｼ撰ｼｶ・ｭ・｡・ｧ ・､・･・ｭ・ｰ・ｯ・ｷ・･・ｲ ・ｭ・｡・ｧ・擾ｼ､・･・ｭ・托ｼ抵ｼ難ｼ・・・・厄ｼ暦ｼ假ｼ呻ｼ・・托ｼ撰ｼ托ｼ抵ｼ難ｼ・・・・厄ｼ暦ｼ假ｼ呻ｼ・・托ｼ撰ｼｭ・｡・ｧ縲・｡・､・ｪ・・・､・･・ｭ縲・｡・､・ｪ・・55280300・ｭ・ｯ・､・･・ｬ縲縲・･・ｰ・ｳ・搾ｼｰ・抵ｼ托ｼ撰ｼ撰ｼ｢・｡・ｭ・ｰ・弱縲縲・托ｼ撰ｼ撰ｼ｡120190・費ｼ済・ｼ・165笆Model designation笆A guide for selection笆EP-Q type holding power characteristic笆Relation between chuck models and holding powerComparison of holding power of chucks of same size笆Holding power笆｡50 generates the max. holding power of 2.94 kN (300 kgf) or over per poleand 笆｡70 generates 5.88 kN (600 kgf) or over per pole.窶ｻFor more information,縲please contact us.笆EPS-P EP Chuck Master*縲Compact design for limited installation space.笆Options縲 竭 Straightening block; for 笆｡50 and 笆｡70 (KT-Q)竭｡ Separately installed feeder boxRecommended for applications thatrequire frequent connector connection/disconnection.笆Model of special specifi cationCHUCK・哘P-QN5-3060APole size・・窶ｦ笆｡50 7窶ｦ笆｡70・俄ｦ窶ｦNormal (Ribs arranged between poles)窶ｦ窶ｦStrong (Poles arranged densely)Chuck sizeNS笳輯izes other than the standard sizes listed on page 31 are also available.笳週he recommended maximum one-piece size is W1200 ﾃ・L1500 mm.縲For other larger sizes, please contact us.笳蹴ound chucks are also available.General milling QNPlanomiller, horizontal M/C, useof straightening blocks, etc. QSGood holding conditionssuch as plate machining.Poor holding conditionssuch as heavy duty cuttingSelection of pole size 笆｡50 or 笆｡70笳週he 笆｡70 size is superior in the absolute holding power and gap characteristic.笳週he 笆｡50 size is recommended for relatively small and thin workpieces. (The platethickness of magnetic saturation is 20 to 25 mm for 笆｡50 and 30 to 35 mm for 笆｡70.)縲・n example of calculation縲峨縲縲縲 Max. holding power on whole attractive face of EP-QS5-4080A縲縲縲縲縲 2.94kNﾃ・0・・umber of poles・会ｼ・76.4kN・・8000kgf・扁ap・・m・・. Relation between gap and holding power縲 Holding on whole face.縲縲縲 ・・N・欝hickness・・m・羽olding power Holding power1. Relation between workpiece thickness and holding power縲Test piece held by 4 poles縲縲縲 ・・N・・ 10 20 40 5030152503020105笆｡70type笆｡50type0 0.1200150100500.2 0.3 0.4 0.5EP-QS7-4080AEP-QS5-4080AEP-QN7-4080AEP-QN5-4080AKT-Q50MEPS-P2100B-2・ｻmm・・n・会ｼｽModel EPS-P2100B EPS-P2100B-2Dimensions・・ﾃ幽ﾃ優・・190・・.48・嘉・65・・.5・嘉・55・・0.0・臼ower source Single-phase, 200 VAC 50/60 HzOutput capacity 10 VDC ? 90 VDC pulse 100 AOutput switchover No switchover 2Magnetizing time (approx.)繝ｻdemagnetizing time (approx.) 1 sec. 3 sec.Breaker capacity (ref.) 30AMass 7.5kg・・6.5・・7.6kg・・6.7・俄ｻThe power cable must be larger than 3.5 mm2 and less than 10 m.ModelType笆｡50・・.96・嘉幽28・・.10・・笆｡70・・.75・嘉幽37・・.45・卯T-Q50 KT-Q70 StationaryKT-Q50M KT-Q70M Movable・ｻmm・・n・会ｼｽ窶ｻThe H dimension is the standard height.EP-QX50-S笳集hen workpieces are hardened steel or special steel, theymay be diffi cult to demount due to strong residual magnetism.In these cases, Model EP-D (P. 34) is recommended.EP-Q / EPS-P / KT-Q32CHUCKCONTROLLERSPERMANENTMAGNETIC CHUCKSPERMANENTELECTROMAGNETIC CHUCKSBLOCKSFOR MCVACUUMCHUCKSPROMELTA*SYSTEMSINE BARCHUCKSHOLDINGTOOLSBLOCKS, HOLDERS,MINI CHUCKSMEASURINGTOOL HOLDERSMAGNETICTOOLSMAGNETICHOLDERSELECTROMAGNETICCHUCKS
