This page is an overview of MAGNET_GENERAL_CATALOG on page44
Move to the page after second(s).
Now go to the page by clicking "Open the e-Book" button.
This e-Book is not available in your environment.
MAGNET_GENERAL_CATALOG
Model EPZ-U TILT TYPE PERMANENT ELECTROMAGNETIC CHUCKModel EPTW-N PERMANENT ELECTROMAGNETIC MICROPITCH CHUCKPowersavingMinimalheatgenerationPowersavingMinimalheatgenerationEPZ-1030UFL 1L 2P Le12H1H2h1h 2B 1BeB2GPower cord 2 m Back stopper・ｻApplication・ｽSuitable for angle grinding on grinders. Easy to install.・ｻFeatures・ｽ笳週he rotary shaft with scale facilitates angle setting. (Anangle can be set as desired in a range of 90ﾂｰ forwardand 90ﾂｰ backward.)笳輯ince electricity is supplied momentarily only to controlthe magnetomotive force when mounting/demounting aworkpiece, little heat is generated internally to enablehighly precise machining.笳輯ince electricity needs not be supplied continuously evenwhile holding a workpiece, the running cost is very low.笳輯ince the holding power is maintained in the event of powerfailure and cable breakage, safety is secured.・ｻmm・・n・会ｼｽ窶ｻThe chuck controller and clamp parts are not included. 窶ｻThe KANETEC chucks work best when a KANETEC chuck controller is used.窶ｻTurning the permanent electromagnetic chucks on and off must be limited to once per several minutes. If on/off operations are repeated frequently, the chucks may be damaged by overheat.Model Nominal SizeWork Face Pole Pitch Tilt Base Length HeightVoltage Mass ElectroB? L? Be Le H? P B? ?? ?? G h? h? L? H? Chuck MasterEPZ-1025UF 100・・.93・嘉・50・・.84・・00・・.93・・50・・.84・・8・・.07・・11・・.30・・00・・.93・・1・・・・・・.43・・.07・・.35・・00・・.93・・0・・.96・・9・・.14・・4・・.55・・0・・.15・・5・・.59・・68・・4.4・・30・・.11・・0 VDC22kg/ 48 lbEPS-215BEPZ-1030UF 100・・.93・嘉・00・・1.8・・00・・1.8・・55・・0.0・・18・・6.4・・4kg/ 52 lbEPZ-1230UF 120・・.72・嘉・00・・1.8・・20・・.72・・96・・.78・・40・・.44・・14・・・・2・・.55・・.07・・.47・・5・・.74・・0kg/ 66 lbEPZ-1530UF 150・・.90・嘉・00・・1.8・・50・・.90・・120・・.72・・145・・.70・・7kg/ 81 lbEPZ-1545UF 150・・.90・嘉・50・・7.7・・450・・7.7・・408・・6.0・・568・・2.3・・52kg/114 lbPowersavingMinimalheatgeneration・ｻApplication・ｽSuitable for precision grinding on grinders and for holding thinand thick workpieces having a large area.・ｻFeatures・ｽ笳週hanks to fi ner pole pitches on the chuck work face, thesechucks hold thin and wide workpieces fi rmly.笳輯ince electricity is supplied momentarily only to control themagnetomotive force when mounting/demounting a workpiece,little heat is generated internally to maintain accuracy.笳輯ince electricity needs not be supplied continuously evenwhile holding a workpiece, the running cost is very low.笳輯ince the holding power is maintained in the event of powerfailure and cable breakage, safety is secured.・ｻApplication・ｽSuitable for grinding of thin and smallworkpieces.・ｻFeatures・ｽ笳秀enerates strong holding power onworkpieces of 笆｡25 mm and larger.笳終nstead of the conventional magneticp o l e l o n g i t u d i n a l p a t t e r n s , t h etransverse magnetic pole patterns areused.笳就 resin-bonded structural face platehaving little environmental burden isemployed.窶ｻThe chuck controller and clamp parts are not included. 窶ｻThe KANETEC chucks work best when a KANETEC chuck controller is used.窶ｻTurning the permanent electromagnetic chucks on and off must be limited to once per several minutes. If on/off operations are repeated frequently, the chucks may be damaged by overheat.・ｻmm・・n・会ｼｽModel Nominal SizeWork Face Pole Pitch Mounting Face HeightVoltage PowerCord Mass ElectroB? L? t Be P B? L? h H Chuck MasterEPTW-1530 150・・.90・嘉・00・・1.8・・50・・.90・・00・・1.8・・20・・.78・・125・・.92・・・・.8・・.2・・.15・・.03・・.12・・48・・.82・・00・・1.8・・18・・.70・・5・・.74・・0 VDC2m・・8.7・・9kg/ 63 lbEPS-215BEPTW-1545 150・・.90・嘉・50・・7.7・・450・・7.7・・450・・7.7・・44kg/ 97 lbEPTW-2040 200・・.87・嘉・00・・5.7・・00・・.87・・00・・5.7・・5・・.98・・73・・.81・・198・・.79・・00・・5.7・・0・・.78・・20・・.72・・5kg/143 lbEPTW-2050 200・・.87・嘉・00・・9.6・・500・・9.6・・500・・9.6・・m・・18・・2kg/180 lbEPTW-2560 250・・.84・嘉・00・・3.6・・250・・.84・・00・・3.6・・17・・.54・・248・・.76・・00・・3.6・・23kg/271 lbEPTW-3060 300・・1.8・嘉・00・・3.6・・300・・1.8・・269・・0.5・・298・・1.7・・147kg/324 lb窶ｻThe chuck controller and clamp parts are not included. 窶ｻThe KANETEC chucks work best when a KANETEC chuck controller is used.窶ｻTurning the permanent electromagnetic chucks on and off must be limited to once per several minutes. If on/off operations are repeated frequently, the chucks may be damaged by overheat.・ｻmm・・n・会ｼｽModel Nominal SizeWork Face Pole Pitch Mounting Face HeightVoltage PowerCord Mass ElectroB? L? t Le P B? L? h H Chuck MasterEPTW-N1530 150・・.90・嘉・00・・1.8・・50・・.90・・00・・1.8・・5・・.98・・61・・0.2・・・・・・・・.15・・.04・・.11・・48・・.82・・14・・2.3・・0・・.78・・00・・.93・・80 VDC2m・・8.7・・0kg/ 66 lbEPS-W215BEPTW-N1545 150・・.90・嘉・50・・7.7・・450・・7.7・・397・・5.6・・464・・8.2・・45kg/ 99 lbEPTW-N2040 200・・.87・嘉・00・・5.7・・00・・.87・・00・・5.7・・349・・3.7・・98・・.79・・14・・6.2・・10・・.33・・2kg/114 lbEPTW-N2050 200・・.87・嘉・00・・9.6・・500・・9.6・・449・・7.6・・514・・0.2・・m・・18・・5kg/143 lbEPTW-N2560 250・・.84・嘉・00・・3.6・・250・・.84・・00・・3.6・・549・・1.6・・46・・.68・・14・・4.1・・07kg/235 lbEPTW-N3060 300・・1.8・嘉・00・・3.6・・300・・1.8・・296・・1.6・・128kg/282 lbModel EPTW PERMANENT ELECTROMAGNETIC MICROPITCH CHUCKEPTW-1530EPTW-N2040Be PB 2B 1L 1LhHt2 8 8Side stopper Back stopper Power cord 2 ? 3 mEnvironmentallyfriendlyEnvironmentallyfriendlySidestopperPowercordB 2BP1LeHh tL 1L 2Chuck controllerrequired additionallyChuck controllerrequired additionallyChuck controllerrequired additionally37 CHUCKCONTROLLERSPERMANENTMAGNETIC CHUCKSPERMANENTELECTROMAGNETIC CHUCKSBLOCKSFOR MCVACUUMCHUCKSPROMELTA*SYSTEMSINE BARCHUCKSHOLDINGTOOLSBLOCKS, HOLDERS,MINI CHUCKSMEASURINGTOOL HOLDERSMAGNETICTOOLSMAGNETICHOLDERSELECTROMAGNETICCHUCKSPERMANENT ELECTROMAGNETIC CHUCKS