This page is an overview of MAGNET_GENERAL_CATALOG on page54
Move to the page after second(s).
Now go to the page by clicking "Open the e-Book" button.
This e-Book is not available in your environment.
MAGNET_GENERAL_CATALOG
Types of Sine Bar ChucksThe sine bar chucks are used to set accurate angles ofworkpieces for highly precise grinding or as an inspection fixture.This is a type of chuck that utilizes angle setting by a sine barand the chuck work face can be set to a desired angle effi ciently.■FeatureThe sine bar chucks come in various types such as electromagnetic, water-cooled, permanent electromagnetic, permanentmagnetic and in various sizes.Type Model Features RemarksRotary electromagnetic SBE-U Dust cover provided on gauge blockRotary water-cooled electromagnetic SBC-U High precision water-cooled typeRotary permanent electromagnetic SBEP-U Momentary power application for minimizedheat generationRotary permanent magnetic SBP-U Dust cover provided on gauge blockSine bar chuck compound type SBP-R・LS Thin compound typeSine bar chuck single typeSBP-R・S Thin single typeSBP-R・L Tilting in longitudinal direction※The rotary tilting sine bar chuck comes with a gauge block (for 0° setting) of 25.882 mm of JIS Class B.SBE-USBP-R・LSSBP-R・LSBP-R713Gauge block setting location on the right side(photo): R type, and on the left side: L type.The lock lever is installed on both sides.Model SBE-U TILT TYPE ELECTROMAGNETIC SINE BAR CHUCKSBE-1131UFR-CEApplicationESuitable for high precision angle grinding of molds and jigs.EFeaturesE●The gauge block can be set on either the right side (R) or left side (L) to meet the rotatingdirection of the grinding wheel of the grinder.●The chuck can be smoothly tilted and easily operated.●An angle can be set finely by one try with the clamp system.●The position can be changed and secured by pulling the lever in the axial direction.●When the dustproof cover of the gauge block is opened beyond about 60 degrees, it islocked to facilitate setup and cleaning.Power cord14165E20PLeL280138H1 8425 32110100L1 B145°15°25.88290515.5Chuck controller required additionallyModel NominalSizeWork Face Pole Pitch MountingLength HeightTiltAngleAngleAccuracy Voltage Current Mass ElectroChuck Master RemarksB? L? Le H? P L? Angle 0°,Min.Cover fullyopen, Max.SBE-1131UFR-C110EE.33EÁE15EE2.4EE10EE.33EE15EE2.4EE78EE0.9EE13EE.44EE1EEEEEE.43EE.11EE.31EE92EE9.3EE38EE.43EE10EE.26EE15°?EE5°0.007/100max. 90 VDC 0.3A 36kg/79 lbES-M103BES-M305BEH-V305A※ For types with a combination ofa rectifi er and demagnetizer, seepages ofSBE-1131UFL-C “Chuck Controllers. EP17?P20EmmEEnE］※The type having the gauge block setting area on the right side is indicated by “R Eand that on the left side indicated by “L E※The chuck controller and clamp parts are not included. The KANETEC chucks work best when a KANETEC chuck controller is used.※A gauge block (25.882 mm) for 0° is included. For the mechanism of angle setting, see the bottom part on page 51. The conversion table included with the product facilitates angle setting.Environmentallyfriendly47 CHUCKCONTROLLERSPERMANENTMAGNETIC CHUCKSPERMANENTELECTROMAGNETIC CHUCKSBLOCKSFOR MCVACUUMCHUCKSPROMELTA*SYSTEMSINE BARCHUCKSHOLDINGTOOLSBLOCKS, HOLDERS,MINI CHUCKSMEASURINGTOOL HOLDERSMAGNETICTOOLSMAGNETICHOLDERSELECTROMAGNETICCHUCKSSINE BAR CHUCKS