This page is an overview of MAGNET_GENERAL_CATALOG on page55
Move to the page after second(s).
Now go to the page by clicking "Open the e-Book" button.
This e-Book is not available in your environment.
MAGNET_GENERAL_CATALOG
Model SBC-U TILT TYPE WATER-COOLED ELECTROMAGNETIC SINE BAR CHUCKModel SBEP-U TILT TYPE PERMANENT ELECTROMAGNETIC SINE BAR CHUCK�E�Application�E�Constructed to enable real-time internal cooling of heat generated whenpower is applied to the electromagnet, making these chucks suitable forhigher precision grinding operation.�E�Features�E�●Change in accuracy is minimized by supplying coolant at a fl ow rate of2 to 4 L/min to minimize coil heating.●The mechanical functions and features are almost the same as thoseof Model SBE chucks.Chuck controller required additionally90P25 32515.5801381416511010045°15°25.882R2084Power cordLeL1L2H1B1Chuck controller required additionally84Le90P(7)25 32515.580138Power cordL11416511010045°15°25.882�E�20B1H1L2�E�Application�E�These chucks are recommended for angle grinding of molds and jigs. Sincemagnetization is carried out by momentary power application, almost no heatis generated to make this model suitable for high precision grinding.�E�Features�E�●Electricity is applied momentarily. No electricity is required to maintain theholding power during grinding, thus saving energy.●The holding power is maintained in the event of power failure duringgrinding, thus enhancing safety.●The mechanical functions and features are almost the same as those ofModel SBE.�E�mm�E�En�E�］※The type having the gauge block setting area on the right side is indicated by “R Eand that on the left side indicated by “L E ※A cooler unit is required additionally.※The chuck controller and clamp parts are not included. The KANETEC chucks work best when a KANETEC chuck controller is used.※A gauge block (25.882 mm) for 0° is included. For the mechanism of angle setting, see the bottom part on page 51. The conversion table included with the product facilitates angle setting.Model NominalSizeWork Face Pole Pitch MountingLength HeightTiltAngleAngleAccuracy Voltage Current MassElectroChuckMasterRemarksB? L? Le H? P L? Angle 0°,Min.Cover fullyopen, Max.SBC-1131UFR-C110�E�E.33�E�ÁE15�E�E2.4�E�E10�E�E.33�E�E15�E�E2.4�E�E78�E�E0.9�E�E13�E�E.44�E�E1�E�E�E�E�E�E.43�E�E.11�E�E.31�E�E92�E�E9.3�E�E38�E�E.43�E�E10�E�E.26�E��E15°?�E�E5° 0.007/100max. 90 VDC 0.3A 36kg/79 lbES-M103BES-M305BEH-V305A※For models with a combination of a rectifi er and demagnetizer, see pages ofSBC-1131UFL-C “Chuck Controllers. EP17?P20�E�mm�E�En�E�］※The type having the gauge block setting area on the right side is indicated by “R Eand that on the left side indicated by “L E※The chuck controller and clamp parts are not included. The KANETEC chucks work best when a KANETEC chuck controller is used.※A gauge block (25.882 mm) for 0° is included. For the mechanism of angle setting, see the bottom part on page 51. The conversion table included with the product facilitates angle setting.Model NominalSizeWork Face Pole Pitch MountingLength HeightTilt Angle AngleAccuracy Voltage Current Mass ElectroChuck MasterB? L? Le H? P L?Angle 0°,Min.Cover fullyopen, Max.SBEP-1131UFR-C 110�E�E.33�E�ÁE15�E�E2.4�E�E10�E�E.33�E�E15�E�E2.4�E�E78�E�E0.9�E�E13�E�E.44�E�E1�E�E�E�E�E�E.43�E�E.11�E�E.31�E�E92�E�E9.3�E�E38�E�E.43�E�E10�E�E.26�E�Eー15°?�E�E5° 0.007/100max. 90 VDC 2.1A 36kg/79 lb EPS-215BSBEP-1131UFL-CPowersavingSBC-1131UFL-CSBEP-1131UFR-CSBE-U / SBC-U / SBEP-U48CHUCKCONTROLLERSPERMANENTMAGNETIC CHUCKSPERMANENTELECTROMAGNETIC CHUCKSBLOCKSFOR MCVACUUMCHUCKSPROMELTA*SYSTEMSINE BARCHUCKSHOLDINGTOOLSBLOCKS, HOLDERS,MINI CHUCKSMEASURINGTOOL HOLDERSMAGNETICTOOLSMAGNETICHOLDERSELECTROMAGNETICCHUCKS