This page is an overview of MAGNET_GENERAL_CATALOG on page61
Move to the page after second(s).
Now go to the page by clicking "Open the e-Book" button.
This e-Book is not available in your environment.
MAGNET_GENERAL_CATALOG
Suitable as exclusive fi xing jig for round steel bars and irregularly shaped workpieces!Additional workallowed area.(Top/bottom/right/left)Additionally workable up to10 mm on each face.????indicates the attractive face.B L35H8NOFFOANE TECKPin CounterboreModel KM-JB SWITCHABLE PERMANENT MAGNETIC HOLDERModel MM FREE BLOCK・ｻApplication・ｽIn addition to using these holders as a fixing jig for small workpieces, they canbe used as a block to support 3 points of a workpiece during grinding.・ｻFeatures・ｽ笳拾ach face can be worked additionally for up to 10mm. (The on/off operationface and rear face are excluded.)笳州y using these holders as exclusive jigs for a particular workpiece, the workeffi ciency is improved.笳就s these holders are of drip-proof construction, they can be used in liquidsuch as during electric discharge machining.KM-JB0709KM-JB side faceKM-JB0812窶ｻ However, avoid making a holein the pin and counterbore areas.Model HoldingPowerDimensionsMassB L HKM-JB0709 392N・・0kgf・・65・・.55・・85・・.34・・70・・.75・・2.5kg/ 5.5 lbKM-JB0812 883N・・0kgf・・80・・.14・・120・・.72・・90・・.54・・5.5kg/12.1 lb窶ｻThe holding power is based on a test piece of 笆｡50 ﾃ・t25, S15C. 窶ｻA hex wrench key is included.・ｻmm・・n・会ｼｽFreely workable permanent magnetic block窶ｻThe holding power is a reference value obtained using a test piece of S15C, 笆｡50 ﾃ・t25, ground surface.窶ｻNote that when workpieces are held on two or more faces simultaneously, the holding power of each face drops.・ｻApplication・ｽThese blocks are designed to allow deep engraving such asgrooves and steps on the attractive face to fit workpiece shapeswhen holding workpieces.・ｻFeatures・ｽ笳週he attractive face can be removed up to 10 mm deep from thesurface of the new block.笳就s workpieces can be fitted in grooves, a large machiningpressure can be used. Also cemented carbide workpieces,which are diffi cult to hold by a magnetic chuck, can be securedby using these blocks to enable grinding.笳週hese blocks can be mounted on the magnetic chuck work face.笳週here are two types; a magnetic force ON-OFF type and a typenot equipped with an ON-OFF function.MM2F-512MM3F-612MM3F-912MM3Y-1023Model NominalSizeHoldingPowerDimensions Pole Pitch Work Allowance Mag. ForceON/OFF MassB L H B? H? P tMM2F- 512 50・・.96・嘉・20・・.72・・00N・・0kgf・・0・・.96・・20・・.72・・0・・.96・・0・・.57・・40・・.57・・・・・・・・.31・・.11・・.19・・Max.10・・.39・丑otprovided2kg/4.4 lbMM3F- 612 60・・.36・嘉・20・・.72・・00N・・0kgf・・0・・.36・・.5kg/5.5 lbMM3F- 912 90・・.54・嘉・20・・.72・・00N・・0kgf・・0・・.54・・0・・.75・・.5kg/7.7 lbMM3Y-1023 100・・.93・嘉・30・・.05・・50N・・5kgf・・00・・.93・・30・・.05・・00・・.93・・0・・.15・・0・・.54・・5.2・・.59・・Provided 20kg/44 lb・ｻmm・・n・会ｼｽ縲・M2F-512縲・ attractive facesLtHH 1BBtp1ON縲・M3Y-1023縲隠BLPt tt1HH 120450 25010300縲・M3F-612繝ｼ912縲・ attractive facesLtHH 1BBt tp1indicates the attractive face.RMAW-2F / KPB / KM-JB / MM54CHUCKCONTROLLERSPERMANENTMAGNETIC CHUCKSPERMANENTELECTROMAGNETIC CHUCKSBLOCKSFOR MCVACUUMCHUCKSPROMELTA*SYSTEMSINE BARCHUCKSHOLDINGTOOLSBLOCKS, HOLDERS,MINI CHUCKSMEASURINGTOOL HOLDERSMAGNETICTOOLSMAGNETICHOLDERSELECTROMAGNETICCHUCKS