This page is an overview of MAGNET_GENERAL_CATALOG on page64
Move to the page after second(s).
Now go to the page by clicking "Open the e-Book" button.
This e-Book is not available in your environment.
MAGNET_GENERAL_CATALOG
・ｻmm・・n・会ｼｽ窶ｻThe holding power is based on the V face and ﾏ・0 round steel bar. 窶ｻFor accuracy, see the table below.窶ｻNote that when workpieces are held on two or more faces simultaneously, the holding power of each face drops.Model Holding Power Applicable DiameterDimensionsMassB H L aKMV- 50D 150N・・5kgf・頴r over. ﾏ・8・・.31・峨・ﾏ・50・・.96・・40・・.57・・0・・.96・・0・・.75・・6・・.41・・1kg/2.2 lbﾃ・KMV- 80D 200N・・0kgf・頴r over. ﾏ・8・・.31・峨・ﾏ・80・・.14・・50・・.96・・0・・.14・・00・・.93・・0・・.36・・3kg/6.6 lbﾃ・KMV-125D 230N・・3kgf・頴r over. ﾏ・8・・.31・峨・ﾏ・25・・.92・・100・・.93・・50・・.90・・0・・.54・・5kg/ 11 lbﾃ・笆The dimensional accuracy of KVS and KMV is based on KANETEC in-house standards. If you require higher accuracy, please contact us.Model KVS MAGNETIC V-HOLDER・ｻApplication・ｽSuitable for securing irregularly shaped workpieces for grinding and light dutycutting such as drilling and tapping.・ｻFeatures・ｽ笳週he special construction exerts a strong magnetic force on three faces of top,bottom and end.笳酋sable for inspection also. Two accuracy grades; standard and special areavailable.笳週he magnetic force can be turned on and off easily by turning the lever.笳愁rip-proof construction.Ba1590ﾂｰ・・C groove・羽L5 525 2590ﾂｰ・・E groove・唄ide face Side faceBottom faceEnd faceTop faceindicates the attractive face.ModelHolding Power Applicable Diameter DimensionsMassSteel bar VC groove VE groove B a L HKVS-1B 0.7kN・・70kgf・・ﾏ・・・.31・峨・ﾏ・8・・.67・珂・・・.31・峨・ﾏ・0・・.78・・5・・.95・・0・・.96・・00・・.93・・105・・.13・・.5kg/ 9.9 lbKVS-2B 1.0kN・・00kgf・・200・・.87・・9.0kg/19.8 lb窶ｻThe holding power is based on ﾏ・0 round steel bar. 窶ｻFor accuracy, see the table below.窶ｻNote that when workpieces are held on two or more faces simultaneously, the holding power of eachface drops.・ｻmm・・n・会ｼｽModel繝ｻAccuracyItemKVS-1B KVS-2BStandard Special Standard SpecialParallelismBottom face to top face12 7 20 12Bottom face to VC grooveTop face to VE grooveSide face to side faceSquareness Bottom face to side face 21 10 21 15・夷ｼm・・笆KVS accuracy窶ｻIf you require higher accuracy, specify the required grade.縲窶ｻIf you require special accuracy on areas not listed in the table, please contact us.Model繝ｻAccuracyItemKMV-50D KMV-80D KMV-125DStandard Special Standard Special Standard SpecialParallelismBottom face to top face107158209Bottom face to V faceSide face to side face 12 15End face to V face 20 25 30Flatness of bottom face 10 15 20Squareness Bottom face to end face 20 10 25 12 30 14Difference in height of V faces of one set of blocks 7 8・夷ｼm・・笆KMV accuracyModel KMV MAGNETIC V-BLOCKKVS-1BKVS-2BKMV-50DKMV-125DKMV-80D・ｻApplication・ｽHolding tools for round bar marking and drilling.Holding tools for three-dimensional measuringinstruments and various measuring systems.・ｻFeatures・ｽ笳集orkpieces can be held on the top face (V face)and end face.笳週he ON/OFF lever is detachable. (The length ofthe opposite sides of the hex hole is 8 mm.)笳愁rip-proof and oil-resistant construction.笳週wo blocks make one set.笳酋ltra-precision fi nishing is also available. Pleasecontact us.Ha90ﾂｰEndfaceTopfaceSidefaceSidefaceBottomfaceLBindicate the attractive face.57 CHUCKCONTROLLERSPERMANENTMAGNETIC CHUCKSPERMANENTELECTROMAGNETIC CHUCKSBLOCKSFOR MCVACUUMCHUCKSPROMELTA*SYSTEMSINE BARCHUCKSHOLDINGTOOLSBLOCKS, HOLDERS,MINI CHUCKSMEASURINGTOOL HOLDERSMAGNETICTOOLSMAGNETICHOLDERSELECTROMAGNETICCHUCKSBLOCKS, HOLDERS, MINI CHUCKS