BookTitleMAGNET_GENERAL_CATALOG

Summary

MAGNET_GENERAL_CATALOG

※The holding power is based on ρE0 round steel bar.�E�Application�E�These blocks are used to hold small-diameter round barson optical measuring equipment. (Non-watertight type)�E�Features�E�●One set consists of two blocks. The attractive facesand other work faces have been fi nished precisely. Theblocks can be turned ON and OFF by 90° turning usinga screwdriver on the bottom face.■The dimensional accuracy of KMV-M is based on KANETEC in-house standards. If you require higher accuracy, please contact us.WorkpieceMV�E�ENSAn example of usage �E�Application�E�This adapter itself is not magnetic, but when it is placed on a V-holder having the N poleand S pole on separate sides like Model KVA, it induces magnetism to hold small diameterworkpieces that cannot be physically mounted directly. (See the figure below.) This adapteris recommended for holding workpieces during grinding, drilling and measurement.�E�Features�E�●The attractive face can be setto any angle between 90 and180 degrees.●The hinge part acts as aseparator to divide magnetic80 �E�E2�E�Epoles.10Folding direction※KTV-1 applicable diameter:ρE0?ρE0 mm ※If you require additional working on the blocks, please contact us.�E�mm�E�En�E�］ModelDimensions Pole PitchMassB L H P? P?KT-1 70�E�E.75�E�E100�E�E.93�E�E41�E�E.61�E�E3.2�E�E.12�E�E.2�E�E.12�E�E.0kg/4.4 lbÁEKT-2 45�E�E.77�E�E72�E�E.83�E�E22�E�E.86�E�E�E�E.11�E�E.37kg/0.8 lbÁEKT-3125�E�E.92�E�E50�E�E.90�E�E8�E�E.49�E�E4.5�E�E.17�E�E.4kg/12 lbKT-4 304�E�E1.9�E�E2�E�E.07�E�E11.7kg/25 lbKTV-1 60�E�E.36�E�E65�E�E.55�E�E40�E�E.57�E�E3�E�E.11�E�E3.2�E�E.12�E�E0.78kg/1.7 lbÁEAn example of usage、ET-1、E、ETV-1、E、ET-2、E、E〉Model KMV-M PERMANENT MAGNETIC MINI V-BLOCKKMV-M025KMV-M032Model MV MINI V-ADAPTERModel KT.KTV CHUCK BLOCKMV-1KTV-1KT-1KT-4NN S N S N S N SS N S N S N SP 1 P 2LBH90°P 1 P 2LBHP1 P HL2BNameplateTightening boltItem Model・Accuracy KMV-M020 KMV-M025 KMV-M032ParallelismBottom face to top face10 10 10Bottom face to V faceSide face to side faceSide face to V faceEnd face to end faceFlatness of bottom face 5 5 5SquarenessBottom face to side faceBottom face to end face 21 21 21End face to V faceDifference in height between V face and top face of one set of blocks 7 7 7�E�μm�E�E■KMV-M accuracy�E�Application�E�These blocks are used in combination with amagnetic chuck as an auxiliary tool to hold roundbars and sheet-like workpieces that are difficult tohold on the work face alone.�E�Features�E�●Since these blocks are not magnetized themselves,they are placed on a magnetic chuck to inducemagnetism to hold workpieces. Magnetism can beinduced on two faces of the top face and side faceor the V face and side face.●Workpieces of special shapes can also be held byuse of chuck blocks, thus making it possible toutilize your chucks in stock.●One set of two blocks has been finished together.(KT-3 and -4 are available individually.)(Bottom face)Side face Side faceTop face90°�E��E�Ｂ3 �E�1 �E�3�E�End face End face HBottom face (ON/OFF switchover face)�E�indicates theattractive face.�E�mm�E�En�E�］Model Holding Power ApplicableDiameterDimensionsMassB B? B? B3 H LKMV-M020 9.8N�E�Ekgf�E�EρE5�E�E.59�E�E20�E�E.78�E�E12�E�E.47�E�E2.0�E�E.07�E�E4�E�E.15�E�E20�E�E.78�E�E20�E�E.78�E�E0.06kg/0.13 lbÁEKMV-M025 19.6N�E�Ekgf�E�EρE0�E�E.78�E�E25�E�E.98�E�E15�E�E.59�E�E2.5�E�E.09�E�E5�E�E.19�E�E25�E�E.98�E�E25�E�E.98�E�E0.13kg/0.28 lbÁEKMV-M032 49 N�E�Ekgf�E�EρE5�E�E.98�E�E32�E�E.25�E�E20�E�E.78�E�E3.0�E�E.11�E�E6�E�E.23�E�E32�E�E.25�E�E32�E�E.25�E�E0.24kg/0.53 lbÁE※If you require higher accuracy, please contact us.■Model:MV-1■Dimensions:80�E�E.14�E�ÁE42�E�E 1.65�E�ÁE0�E�E.39�E�Emm�E�En�E�■Mass:250 g/ 0.55 lb ■Parallelism:0.006 ■HardenedKVS / KMV / KMV-M / KT.KTV / MV58CHUCKCONTROLLERSPERMANENTMAGNETIC CHUCKSPERMANENTELECTROMAGNETIC CHUCKSBLOCKSFOR MCVACUUMCHUCKSPROMELTA*SYSTEMSINE BARCHUCKSHOLDINGTOOLSBLOCKS, HOLDERS,MINI CHUCKSMEASURINGTOOL HOLDERSMAGNETICTOOLSMAGNETICHOLDERSELECTROMAGNETICCHUCKS