Summary
MAGNET_GENERAL_CATALOG
Model NH MAGNETIC TYPE NOZZLE HOLDERModel MDR MAGNETIC DRESSERModel MP MAGPAD*30LHW30 333 13 133NH-P3An example of usageAn example of NH-M1 usageNH-P1NH-M3NH-M1(Available separately)�E�Application�E�This holder is used to supply cutting fl uid or air to machine tools.This can also be used to remove chips and particles producedduring electric discharge machining by injecting cutting liquid.�E�Features�E�●Compared with conventional products, flexibility has beenextremely improved. The fl exible part can be bent freely. (NHM1,M3)●By employing a metallic flexible part, the holding posture ismaintained stably even when releasing high pressure air or alarge amount of cutting fl uid. In addition, it is highly resistantto thermal damage by chips and its durability has beenimproved. (NH-M1, M3)●The powerful magnet enables the holder to be mounted in anyposition easily.●The nozzle tip cab be positioned in any posture and at anyangle.●The holder is equipped with a valve to enable adjustment ofthe fl ow rate.●The adjustable hose can be adjusted in length by removing oradding joints. (NH-P)※Upper limit of pressure …Adjustable hose (NH-P1, P3) : Air pressure 0.34 MPa, liquid pressure 0.2 MPa Metallic fl exible hose (NHM1,M3) : 0.6 MPa max. (Upper limit of fl ow rate: 10 litters/minute max.). However, depending on releasingangles, the posture of the hose may be changed by a jetting pressure even when the air/liquid pressure isbelow the upper limit. In such a case, turn the valve to reduce the fl ow rate.※The hose length includes the stainless steel nozzle part (NH-P: 70 mm) at the tip.※The holding power is based on a test piece of SS400, 10 mm thick, ground surface.※The magnet section of NH-M and NH-P is common. Therefore the upper section is interchangeable for mounting between NH-M and NH-P.※NH-M1, M3: Flexible part ρE1 mm�E�mm�E�En�E�］Model Holding Power Nominal Size Inlet Dia. Hose Length No. of Outlets MassNH-P1 250N�E�E5kgf�E�EρE0�E�E.75�E�ÁE7�E�E.06�E�ρE�E�E.35�E�E90�E�E5.3�E�E1 pc 0.95kg/2.1 lbNH-P3 500N�E�E0kgf�E�E48�E�E.89�E�ÁE3�E�E.87�E�ÁE4�E�E.12�E�E420�E�E6.5�E�E3 pcs 1.65kg/3.6 lbNH-M1 245N�E�E5kgf�E�EρE0�E�E.75�E�ÁE1�E�E.22�E�E400�E�E5.7�E�E1 pc 0.9kg/1.9 lbNH-M3 490N�E�E0kgf�E�E48�E�E.89�E�ÁE3�E�E.87�E�ÁE4�E�E.12�E�E400�E�E5.7�E�E3 pcs 1.9kg/4.1 lb�E�Application�E�A dressing tool for grinding wheels.The dresser can be held firmly on a powerful magnetic holder base. Settingup is easy and reliable.�E�Features�E�●The magnetic force can be turned on and off with the lever to facilitatemounting to and demounting from the machine table.(For setting on amagnetic chuck, power OFF the chuck and power ON this Dresser.)●The dresser can be mounted at any angles.●The dresser mounting clamp can be secured to either the side or the top ofthe magnetic holder base. (The photo shows the clamp mounted on the side.)MDR-1CThe dresser is not included.�E�mm�E�En�E�］Model Holding PowerDimensionsDresser Shaft Dia. MassWidth Length HeightMDR-1C 800N�E�E0kgf�E�E50�E�E.96�E�E58.5�E�E.30�E�E55�E�E.16�E�EρE1�E�E.43�E�Eand ρE2�E�E.47�E�E1.2kg/2.64 lb�E�Application�E�The Magpad is a device to prevent wire breakage by heat due toaerial discharge. It protects wire electrodes of wire electricdischarge machines from scattering of coolant which is likely tooccur at the start of discharging. This Magpad can also be usedto prevent dislocation or falling of cut-out pieces at the start orend of cutting.�E�Features�E�●The Magpad is made of transparent acrylic plate incorporatingpowerful magnets. The Magpad has strong holding power andenables it to set a wire while monitoring its position visually.●No mechanical clamp is required. Attaching and detachingcan be done efficiently and without a fear of damagingworkpieces.●Various models are available to suit any workpiece shapes.●There is no fear of rusting and the magnetic force is semipermanent.The Magpad withstands repeated use and※The holding power is based on a test piece of SS400, 20 mm thick, ground surface. therefore is very economical.�E�mm�E�En�E�］Model HoldingPowerDimensionsMassWidth Length HeightMP-1 80N�E�E8kgf�E�E6�E�E.59�E�E6�E�E.02�E�E�E�E.35�E�E5g/0.07 lbMP-2 200N�E�E0kgf�E�E56�E�E.20�E�E70g/0.15 lbMP-3 250N�E�E5kgf�E�E86�E�E.38�E�E110g/0.24 lbMP-3MP-2MP-1M5 screws can be used to detach the Magpadfrom the workpiece.Holdingpower800NNH-P1/NH-M1 Details of thread sizeNH-P3/NH-M3 Details of thread size�E��E��E�／４Ｐ�E��E�／８Ball valve�E��E��E�／４×ρE��！Eose nipple�E�３－Ｐ�E��E�／！E�E��E��E�／４Ball valve�E��E��E�／４×Ｐ�E��E�／８Ball valve�E��E��E�／８×Ｐ�E��E�／８Hose nipple�E�ρE��）Ball valve�E��E��E�／８×Ｐ�E��E�／！E5.5 25.514 9�E��E� �E��E��E��E��E��E�Ｍ�E�Flexible in all directions!!Parts available individuallyMPV-MF / MPV-CL / MPV-F / MPV / NH / MDR / MP60CHUCKCONTROLLERSPERMANENTMAGNETIC CHUCKSPERMANENTELECTROMAGNETIC CHUCKSBLOCKSFOR MCVACUUMCHUCKSPROMELTA*SYSTEMSINE BARCHUCKSBLOCKS, HOLDERS,MINI CHUCKSMEASURINGTOOL HOLDERSMAGNETICTOOLSMAGNETICHOLDERSELECTROMAGNETICCHUCKSHOLDINGTOOLS
