This page is an overview of MAGNET_GENERAL_CATALOG on page79
Move to the page after second(s).
Now go to the page by clicking "Open the e-Book" button.
This e-Book is not available in your environment.
MAGNET_GENERAL_CATALOG
1) The■areas shown in the following figures can beworked on additionally.2) If areas (magnet, separator, main unit structural part)other than the■areas are worked on, the ON-OFFoperation may be disabled or the main unit may bedamaged or disabled in the worst case.3) Additional working may cause a drop in the holding power and strength. Priorto using the base after additional working, always check its performance.4) If a plate is to be mounted on the top face (a tapped hole provided), be sure touse a nonmagnetic material (e.g. aluminum, SUS304, brass plate). If amagnetic material such as iron is mounted on the top face, the holding powerwill drop significantly.Information about additional working on magnetic holder bases※PrecautionsMB-RV�E�MB-W2V�E�MB-W2S�E�MB-MX28F�E�MB-MX40F�E�MB-OXMB-B�E�MB-BV�E�MB-K�E�MB-FXMB-MX20F�E�KM-B1�E�MR-2CMB-PBCommon base typeMB-T3 (Top face tapped hole M20)MB-PLMB-PHKM-B2/MB-2FPG (No tapped hole on top face)MB-PG MB-PRWMB-PMMB-PSL�E�MB-PSXMB-PS MB-0404MB-PRCommon base typeMB-Z(Top face tapped hole, height andattractive face shape are different.)Common base typeCommon base typeCommon base type Common base type(※Height 76 mm for MB-Z)(※1 MB-2FPG: 51.5 mm)(※2 MB-2FPG: 24.5 mm) (※MB-Z has a different shape.)(M20 for MB-Z)(No hole on MB-2FPG)1960 60120141.37.512 1941 4.515 30 30 30 156 61516―M62M8�E�EDG2�E�E5 40 15171135 357036804425522726 18 26�E�E7.4�E�Yoke�E�EGD2�E�E―M6 M1259 6Separator (ZDC2)ρE8(Magnet)ASection A ? AM8 ÁE1.25, depth 710 20�E�E.25�E�E�E�E9.25�E�E12ρE55ρE5A�E�E9.25�E�E�E�E9.25�E�E195012 1958.530 2555�E�E9.7�E�E.51535ρE0(Magnet)40302M340304-M3, depth 6M6, depth 6Separator21936.521.5 30�E�EGD2�E�E1.573�E�E4.2�E�E6.5 7.512 1941 4.5ρE5(Magnet)5Separator (ZDC2)5138―M61.5M830 2555501958.5 58.5117133.77.512 1941 4.5Separator (ZDC2)13.5 30 30 30 13.55 51316―M61.5M10�E�EB-T3:M20�E�ρE5(Magnet)�E�EDG2�E�E0 255550507021.5 30 21.51336.5 36.5 7.5732555ρE93019 12 19�E�E5.4�E�Yoke�E�EGD2�E�E―M6 2―M841 4.5Separator (ZDC2)ρE5(Magnet)5 51.514.53 050�E�E6.3�E�E414 9A5 6ρE4(Magnet)Separator31Section A11.5 7 11.535 2.3 6.7 20 61930�E�E8�E�E05 5 20 5 5ρE5 (Magnet)Separator15.5 9 15.540ρE021.540※※1※2※ ※ρE5(Magnet)Separator (ZDC2)KM-B / MB-2FPG / MR72CHUCKCONTROLLERSPERMANENTMAGNETIC CHUCKSPERMANENTELECTROMAGNETIC CHUCKSBLOCKSFOR MCVACUUMCHUCKSPROMELTA*SYSTEMSINE BARCHUCKSHOLDINGTOOLSBLOCKS, HOLDERS,MINI CHUCKSMEASURINGTOOL HOLDERSMAGNETICTOOLSMAGNETICHOLDERSELECTROMAGNETICCHUCKS