Summary
MAGNET_GENERAL_CATALOG
�E�Application�E�These holders provide strong holding power for temporary holding duringwelding and temporary assembly. These holders can also be used as a block.�E�Features�E�●The holding angle can be set to 45°, 90° and 135°.●The small type is equipped with a pushbutton and the large type with arotary handle for turning on and off the magnetic force.●The V-groove provided makes this holder to generate strong holding poweron curved surface as well as fl at surface of workpieces. KM-SA: ρE and over, KM-S1A: ρE and over�E�Application�E�Usable for temporary holding during welding and temporary assembly. These holdershold workpieces firmly.�E�Features�E�●The holding angle can be set to 15°, 45°, 60°, 90°, 105° and 120°.●The magnetic force can be turned on and off .●The holding power on steel plates is about the same as when both faces of KMS9and S12 are used and at angles other than 105 °, the holding power dropslittle when two faces are used.KM-S1AKM-SAGGGGGGGG45 156017 5 20 54715 456080 32 38 94N SGGGGGGGG112 13232 8011280Holding PowerSteel bar200ー300NSteel plate200ー600NHolding PowerSteel bar600ー900NSteel plate1200ー1400NHoldingPowerSteel plate150ー250N HoldingPowerSteel plate250ー450NKM-S10KM-S13�E�KM-S10�E�＜KM-S13�E�E20132.2�E�５°�E�０°�E�５° �E�５°�E�０５°�E��E��E� �E��E��E�０５°�E�５°�E�２０°�E�０°�E�２０°3.2 3.2�E�８０）（１４）（７４）（３５！E�E�３９）（６９！E�E�５１）（６０）（１０４．４！E5�E�５° �E�５°�E�０５°�E�２０°�E�０°�E�２０°�E��E��E� �E��E��E�０５４５° �E�５°�E�０°2.9 2.9�E�６７）（２８！E�E�３９）（４７）（５４！E�E�４１）（８０）（１４）※The holding power on steel plate is based on a test piece of SS400, 10 mm thick, ground surface.�E�mm�E�En�E�］ModelHolding PowerDimensions MassSteel PlateKM-S10 150ー250N�E�E5ー25kgf�E�E104�E�E.09�E�ÁE95�E�E.74�E�ÁE7�E�E.63�E�E0.9kg/1.98 lbKM-S13 250ー450N�E�E5ー45kgf�E�E132�E�E.19�E�ÁE20�E�E.72�E�ÁE3�E�E.87�E�E1.6kg/3.52 lbModel KM-SA HEXAGONAL MAGNETIC HOLDERModel KM-S HEXAGONAL MAGNETIC HOLDER�E�mm�E�En�E�］ModelHolding PowerDimensions MassSteel bar Steel plateKM-SA 600ー900N�E�E0ー90kgf�E�ａE50ー200N�E�E5ー20kgf�E�ａE200ー1400N�E�E20ー140kgf�E�ａE800ー1000N�E�E80ー100kgf�E�ａE12�E�E.40�E�ÁE12�E�E.40�E�ÁE4�E�E.70�E�E6.0kg/13.2 lbKM-S1A 200ー300N�E�E0ー30kgf�E�ａE50ー 70N�E�E5ー 7kgf�E�ａE00ー 600N�E�E20ー 60kgf�E�ａE100ー 350N�E�E10ー 35kgf�E�ａE60�E�E.36�E�ÁE60�E�E.36�E�ÁE2�E�E.65�E�E.85kg/1.87 lb※The holding power on steel plate is based on a test piece of SS400, 10 mm thick, ground surface.Note : The holding power in �E�E�E�Eis for attraction on one face in the case of double-face attraction.These holders cannot be used for work where heat is applied for long hours. If the magnet is subjected to high temperature,Precautions for use its magnetic force will drop or be lost suddenly, causing the workpiece to come off the attractive face. Exercise caution.89 LIFTINGMAGNET MAGBORE* CHIP & SLUDGECONVEYANCE EQUIPMENTENVIRONMENTALEQUIPMENTMAGNETIZER ANDDEMAGNETIZERMAGNETIC EQUIPMENTFOR CONVEYANCEMAGNETICSEPARATORSMEASURINGTOOLSPOWERFUL MAGNETICSEPARATORSMEASURINGINSTRUMENTSMAGNETICMATERIALSMAGNETIC TOOLS & EQUIPMENTFOR WELDING OPERATIONMAGNETIC TOOLS & EQUIPMENT FOR WELDING OPERATION
